安全氣囊拆裝注意事項
大家都知道安全氣寰是會爆炸的，所以拆裝安全氣囊時一定要小心翼翼，下面就是安全氣囊拆裝注意事項大家瞭解一下。
安全氣囊拆裝注意事項
01 不可使用檢測燈、電壓表、歐姆表等簡單工具，應該用高阻抗萬用表檢測安全氣囊系統的電路及SRS報警燈。
02 拆卸工作必須在點火開關關閉下，並將蓄電池負極電纜線拆下20s以後才能開始
03 不可將安全氣囊放到無人照管的地方，存放時，應將起緩衝作用的面朝上，表面朝上放置。如果安全氣囊在存放時表面朝下，可能會發生意外展開而導致嚴重事故。切勿在安全氣囊總成上放置任何物體。若充氣組件從90mm以上高層落地就不能再用了
04 為防止損壞安全氣裹總成，應便其遠離任何機油、油脂、清潔劑和水等
05 如果車輛發生輕微碰撞，安全氣囊系統雖然沒有觸發，但也應檢查轉向盤襯墊、前排乘客安全氣囊總成、座位安全帶收緊器和安全氣囊感測器
06 氣囊系統只能工作一次，發生事故被引爆後的氣囊必須更換。為安全起見，氣囊系統的所有元件也票更換。
特別提示
01 在使用噴燈或焊接設備時，不得靠近充氣裝置，以防導致安全氣囊自動充氣.
02 在檢修時不要讓轉向盤襯墊、碰撞感測器、座位安全帶收緊器或前排乘員安全氣裹總成直接暴露在熱空氣中或接近火源，充氣元件不能承受65C以上的溫度
03 在拆檢或更換安全氣裹時，切勿將身體正面朝向氣裹總成
___________________________________________________________________________________________
Car airbag disassembly notes
We all know that the airbag will explode, so be careful when disassembling the airbag, the following is the airbag disassembly notes you understand.
Airbag disassembly notes
01 can not use the detection lamp, voltage meter, ohm meter and other simple tools, should use a high impedance multimeter to detect the circuit of the airbag system and the SRS alarm light.
02 The dismantling work must be started only after the ignition is switched off and the negative battery cable is removed for 20s.
03 Do not leave the airbag unattended. Store it with the cushioning side up and the surface facing upwards. If the airbag is stored with the surface facing down, it may accidentally unfold and cause a serious accident. Do not place any objects on the airbag assembly. If the inflatable assembly falls from a height of 90mm or more, it cannot be reused.
04 To prevent damage to the airbag assembly, keep it away from any oil, grease, detergent, water, etc.
05 If the vehicle is involved in a minor collision and the airbag system is not triggered, the steering wheel liner, front passenger airbag assembly, seat belt retractors and airbag sensors should be checked.
06 The airbag system can only work once, and the airbag must be replaced after it has been triggered in an accident. For safety reasons, all components of the airbag system must also be replaced.
Special instructions
01 Do not approach the inflator when using a blowtorch or welding equipment, as this may cause the airbag to inflate automatically.
02 Do not expose the steering wheel liner, crash sensor, seat belt retractor or front passenger airbag assembly directly to hot air or close to a source of ignition during servicing, the inflatable components cannot withstand temperatures above 65C.
03 Do not face the front of your body towards the airbag assembly when removing or replacing the airbag.
0 Comments