跨接啟動前的準備
1 .拉緊駐車制動器
2 將車輛掛到空擋或P擋 (自動擋)。
3 關閉所有電氣附件
在跨接啟動車輛前，先關閉音響系統。否則，會損壞音響系統。當車輛長時間低速行駛(如交通擁堵等)時，請關閉任何不必要的電氣設備。
連接跨接電纜
在跨接啟動車輛時，按如下順序連接跨接電纜:
1將第一條跨接電纜一端夾在有電的蓄電池的正極接線柱上。(蓄電池殼體或端子上有“+”標記)
2 .將這條跨接電纜另一端夾在沒電的蓄電池的正極接線柱上。(端子上有“+”標記)
3將第二條跨接電纜一端夾在有電的蓄電池的負極接線柱上。(蓄電池殼體或端子上有“”標記)
4 連接這條電纜的另一端到沒電車上的車身搭鐵處。
5.跨接起動時，允許提供跨接起動電源的車輛發動機運轉。應在一分鐘內試著起動沒有電的車輛的發動機，並每次打開點火鑰匙的時間不超過5秒。起動後，保持轉速在2000(轉/分鐘)運轉幾分鐘
6 .按相反的順序小心地拆下跨接線，應先拆下負極電纜，再拆下正極電纜。
1、要給跨接電纜確定適當位置，不要繞到發動機艙的旋轉部件上。否則，會損壞車輛和造成人身傷害
2、在最後連接至需要充電的車輛時，不能連接到蓄電池負極(-) 接線柱上。將最後連接的卡夾連接至發動機缸體鋼質托架的螺栓上。最後連接點應盡可能遠離蓄電池。如果將跨接電纜連線到未充電蓄電池負極端子上，可能會產生電弧並可能引起蓄電池爆炸。這將會造成嚴重的人身傷害或損壞車輛.
3、啟動蓄電池已放電的車輛發動機時，應間隔約1分鐘，每次啟動的時間不能超過15秒。
——————————————————————————————————————
Preparation for jumper activation
1 . Tighten the parking brake
2 Put the vehicle into neutral or P gear (automatic).
3 Switch off all electrical accessories
Switch off the sound system before starting the vehicle in the crossover. Otherwise, the sound system will be damaged. Switch off any unnecessary electrical equipment when driving at low speeds for long periods of time (e.g. in traffic jams).
Connecting the jumper cable
When jumpering the vehicle, connect the jumper cables in the following order.
1 Clamp the first end of the jumper cable to the positive terminal of the charged battery. (The battery case or terminal is marked with a "+")
2 . Clip the other end of this jumper cable to the positive terminal of the uncharged battery. (terminal marked with "+")
3. Clamp the second end of the jumper cable to the negative terminal of the charged battery. (Battery case or terminal marked with " ")
4 Connect the other end of this cable to the body hitch on a non-electric vehicle.
5. When jumper starting, allow the engine of the vehicle supplied with jumper starting power to run. Try to start the engine of an unpowered vehicle within one minute and turn on the ignition key for no more than 5 seconds at a time. After starting, keep the engine running at 2000 rpm for a few minutes.
6 . Carefully remove the jumper cables in reverse order, removing the negative cable first and then the positive cable.
Notes on jumper activation
1. Make sure that the jumper cable is properly positioned and does not wrap around the rotating parts of the engine compartment. Otherwise, it will damage the vehicle and cause personal injury.
2. When making the final connection to the vehicle to be charged, do not connect to the negative (-) battery post. Connect the final connection clip to the bolt on the steel bracket of the engine block. The final connection point should be as far away from the battery as possible. If the jumper cable is connected to the negative terminal of an uncharged battery, an arc may be generated and may cause the battery to explode. This will cause serious personal injury or damage to the vehicle.
3. Start the engine of a vehicle with a discharged battery at intervals of approximately 1 minute and for no more than 15 seconds at a time.
0 Comments